embrace

We are all inventors, each sailing out on a voyage of discovery, guided each by a private chart, of which there is no duplicate. The world is all gates, all opportunities.
Ralph Waldo Emerson


Reblogged from youngdreamerlove
youngdreamerlove:

Autumn <3
-follow me

youngdreamerlove:

Autumn <3

-follow me

Reblogged from aerienette
Reblogged from aerienette
Reblogged from kushandwizdom
Reblogged from kushandwizdom
Reblogged from dailyautumn
Reblogged from lateautumnnights
lateautumnnights:

DIY LEAF BOWL

Materials:

Craft store leaf garland, Mod Podge (matte finish), Foam Brush, Balloon, Scissors, Mixing bowl

*Tip: try to find thin, paper-like leaves for your garland. The thinner the leaves, the better they will mold to the shape of your balloon. Also, avoid any plastic-coated leaves.

How To:

1. Begin by snipping the leaves off the strand of garland. Leave about 1/8” at the base.

2. Carefully rip the entire plastic stem (and all the veins!) off of the faux leaves (See image above). This will help the leaves mold to the shape of the balloon.

3. Fill up your balloon to size. We stuck ours inside a mixing bowl to keep it in place.

4. With your mod podge in a cup near by, gently apply a thin layer on top of your balloon, starting in the middle and working your way out.

5. Lay a leaf on top of the wet mod podge and smooth with your fingers or foam brush. Once it’s stuck in place, apply another thin layer of mod podge on top of that leaf. See image below.

6. Repeat, covering any empty spaces with smaller leaves.

7. When you reach about a quarter of the way down the balloon, add one or two leaves to the bottom of the bowl for extra weight and support. Allow to dry at least an hour.

8. When the mod podge is dry, carefully pop your balloon with a pin at the tied end, slowly letting the air out. Don’t be alarmed if the leaves shrink down when the balloon deflates, it will return to its original shape after a minute or so. You may find that some of the mod podge will stick to the edges of your leaves, but you can just pick or cut it off.

9. Use your bowl to hold potpourri or little wrapped halloween candies. We love easy ways to liven up your home decor and this colorful DIY does the job well.

lateautumnnights:

DIY LEAF BOWL

Materials:

Craft store leaf garland, Mod Podge (matte finish), Foam Brush, Balloon, Scissors, Mixing bowl

*Tip: try to find thin, paper-like leaves for your garland. The thinner the leaves, the better they will mold to the shape of your balloon. Also, avoid any plastic-coated leaves.

How To:

1. Begin by snipping the leaves off the strand of garland. Leave about 1/8” at the base.

2. Carefully rip the entire plastic stem (and all the veins!) off of the faux leaves (See image above). This will help the leaves mold to the shape of the balloon.

3. Fill up your balloon to size. We stuck ours inside a mixing bowl to keep it in place.

4. With your mod podge in a cup near by, gently apply a thin layer on top of your balloon, starting in the middle and working your way out.

5. Lay a leaf on top of the wet mod podge and smooth with your fingers or foam brush. Once it’s stuck in place, apply another thin layer of mod podge on top of that leaf. See image below.

6. Repeat, covering any empty spaces with smaller leaves.

7. When you reach about a quarter of the way down the balloon, add one or two leaves to the bottom of the bowl for extra weight and support. Allow to dry at least an hour.

8. When the mod podge is dry, carefully pop your balloon with a pin at the tied end, slowly letting the air out. Don’t be alarmed if the leaves shrink down when the balloon deflates, it will return to its original shape after a minute or so. You may find that some of the mod podge will stick to the edges of your leaves, but you can just pick or cut it off.

9. Use your bowl to hold potpourri or little wrapped halloween candies. We love easy ways to liven up your home decor and this colorful DIY does the job well.

Reblogged from pumpkinsandsweaters
Reblogged from circlingindizziness
Reblogged from eternoutono